How to clean the air filter of weed eaters

A weed eater is a part of the lawn maintenance equipment that no house should be without. If you do the weed cutting on your own, then a weed eater is an important role in this process. Your weed eater is designed to save your effort on the life process. But to keep the best weed trimmer work, like us, it needs the proper air supply.

When the air filters get dirty, the carburetor can’t work properly, the fuel mixture is made improperly and the motor runs poorly. These problems can be prevented by cleaning the air filters of the weed eater after every four or five times of use and this post will teach you how.

  1. Remove the air filters of weed eaters

air filter

The motor design of weed eaters is quite popular. Therefore, the air filters of weed eaters are nearby the back door of the motor. The cover is often placed at the fixed position with only 4 screws. To see the air filters, you need to remove all screws. Use a screwdriver to do that and put these screws in a place you can pay attention to so that you won’t lose them. Remove the cover and clean the inside and outside with a wet cloth. Use different water buckets if you must do to not add more dirt on the air filters. Remove the air filters by pulling them out of the motor. Leave it on another side.

  1. Clean the air filters
  • Pour one gallon of hot or warm water in a bucket. Add a half teaspoon of dish soap into the bucket. Ensure water gets soapy before cleaning the air filters. Find a hard surface and gently knock the air filters against it. Be aware not to touch the actual cloth of the air filters. You should knock off as much of the debris and dirt as possible before cleaning the air filters.
  • When you are satisfied, you can put the air filters into the warm water. The air filters are made from a type of cloth including many pores. When you put them in the water, squeeze them many times to force soap and water through these pores. Remove the air filters from the bucket.
  • Pour out the water and clean the bucket. Now, fill the cool water in the bucket. Put the air filters in the cool water. Grip them and squeeze them many times. You need to clean soap out of the air filters. After done, you can take the air filters out of the bucket and put them in another place to dry.
  1. Replace the air filters

When you’re satisfied with clean and dry air filters, you can put them into the weed eater. The air can slide in place properly. Now, slide the cover on and screw it in the right place. Don’t screw it too tightly.

You should keep the air filters clean to make your best gas weed eater last longer and save money on repairing. Take good care of the weed eater then it will take good care of your garden.

Solar Heating for the Do-It-Yourself

Solar energy is energy that is generated from the sun and then stored for later use. This is an inexpensive and renewable source of energy. You can use solar energy for heating water for your home as well as your home itself. Passive Solar EnergySolar energy is a cost efficient and effective way for many homeowners to heat their homes during the cold winter months. Solar energy systems that do not have pumps and circulation methods for energy transfers are referred to as passive solar energy.

The south facing side of your building is the most important part of these systems. To maximize the amount of energy that can be generated you will need to clear away anything that shades the south side of the building. Windows that face the south side of the home are the keys in DIY solar energy systems. You want to have the largest windows possible to take full advantage of the suns energy. It is also a good idea to install special flooring materials which will absorb the suns warmth and release it back into the room after dark.

This is a direct gain passive solar energy system. One of the disadvantages of this type of system is that it results in a large amount of heat loss. Sunspaces and trombe walls will need to be installed as well in order to prevent this loss of heat. SunspacesThis small greenhouse like area is built into the southern side of the solar structure. Sunlight passing through the glass actually heats the structure.

The air is circulated through the building through the use of proper ventilation.Trombe  Wall
This is a common technique used in passive solar heating systems. This masonry wall is usually between 8 and 16 inches thick and coated with a dark heat absorbing material. It will also be faced with a single or double layer of glass. A small airspace is created by the addition of the glass to the wall.

Heat from the sun is absorbed by the dark coating on the masonry wall after it passes through the glass. This heat is then slowly transferred to the interior of the wall and released. You can improve the effectiveness of a trombe wall by adding a sheet of metal foil that reduces the amount of infrared energy radiated back through the glass. You will often feel more comfortable in a room heated by a trombe wall than one heated with a traditional forced air furnace.